uPD858C PLL Integrated Circuits

Overview

This PLL-circuit use a 10 bit BCD programmable divide-by-N counter for 399 channels.

Down-converting of the frequency to the divider

This PLL Circuit use a Mixer and a X-Tal Oscillator to convert the output frequency f _OUT to the f _IN to the PLL Circuit.
The X-Tal frequency is f _XTAL = f _OUT - f _IN



The output frequency can be changed by changing the mixing-xtal or add a new mixing-xtal to the oscillator.

Pin	Name	Decription
1	LD	Loop Detector output - HIGH=Unlocked LOW=Locked
2	PD out	Phase Detector output
3	AI	Loop filter Amplifier Input
4	AO	Loop filter Amplifier Output
5	PDI	Programable Divider Input
6	RDO	Reference Divider Output
7	FS	Frequency Select input: HIGH= 10kHz - LOW=5kHz
8	1/2R	Referency frequency divided by 2
9	RI	Referency oscillator Input (X-tal)
10	RO	Refeerency oscillator Output (X-tal)
11	FIN	VCO Oscillator Input
12	VCC	Positive Power Supply (+5Volt)
13	P0	BCD programable input 0
14	P1	BCD programable input 1
15	P2	BCD programable input 2
16	P3	BCD programable input 3
17	P4	BCD programable input 4
18	P5	BCD programable input 5
19	P6	BCD programable input 6
20	P7	BCD programable input 7
21	P8	BCD programable input 8
22	P9	BCD programable input 9
23	GND	Ground
24	PO	Programable Divider Output

Modification methods

BCD Programming of uPD858

Ch. No.	Divided by	P0	P1	P2	P3	P4	P5	P6	P7	P8	P9
1	91	1	0	0	0	1	0	0	1	0	0
2	92	0	1	0	0	1	0	0	1	0	0
3	93	1	1	0	0	1	0	0	1	0	0
4	95	1	0	1	0	1	0	0	1	0	0
..	..	..	..	..	..	..	..	..	0
40	135	1	0	1	0	1	1	0	0	1	0

P0 to P3 is ONES
P4 to P7 is TENS
P8 to P9 is HUNDREDS

Explanation of pin function terms

Above each program pin number is now something called "BCD P0WERs" rather than the previous "P0WERS-0F-2". In this system the pins are assigned such that each successive group of pins has a significance 10 times greater than the preceeding group. Within each decimal group the weights still double in the usual binary progression, but here the highest possible number in a group can't exceed "9" or its decimal multiple such as "90", "900", etc. (Assuming there were that many IC pins.)

Each decimal group can only have a maximum of 4 bits. In this IC there are only 10 rather than 12 program pins so the Hundreds Group can never be worth more than (1 + 2) x 100 or 300. Just figure the total binary value of each group in the usual way, multiply it by 1, 1O, or 100 as appropriate, then add all the groups together: 0nes Group + Tens Group + Hundreds Group, etc.

Since each group has a value, the sum of the groups is the N-Code. For Ch.1, the group sum is 1 + (10 + 80) = 91. Try the math yourself for the other channels. Also notice that Pin 22 is permanently grounded (logic "0" ) since its BCD weight is "200", but we never need a code bigger than "135." (100 + 30 + 5.) By using all ten pins (pins 13-22) you see there's a potential frequency capacity of (9 + 90 + 300) = 399 channels if you could .program them all. This fact has been put to great use in modifications! 0nce again, the uPD858 chip had the excess capacity for possible use elsewhere.

CB Radio Banner Exchange

Ch. No.	Divided by	P0	P1	P2	P3	P4	P5	P6	P7	P8	P9
1	91	1	0	0	0	1	0	0	1	0	0
2	92	0	1	0	0	1	0	0	1	0	0
3	93	1	1	0	0	1	0	0	1	0	0
4	95	1	0	1	0	1	0	0	1	0	0
..	..	..	..	..	..	..	..	..	0
40	135	1	0	1	0	1	1	0	0	1	0

Ch. No.	Divided by	P0	P1	P2	P3	P4	P5	P6	P7	P8	P9
1	91	1	0	0	0	1	0	0	1	0	0
2	92	0	1	0	0	1	0	0	1	0	0
3	93	1	1	0	0	1	0	0	1	0	0
4	95	1	0	1	0	1	0	0	1	0	0
..	..	..	..	..	..	..	..	..	0
40	135	1	0	1	0	1	1	0	0	1	0

Ch. No.	Divided by	P0	P1	P2	P3	P4	P5	P6	P7	P8	P9
1	91	1	0	0	0	1	0	0	1	0	0
2	92	0	1	0	0	1	0	0	1	0	0
3	93	1	1	0	0	1	0	0	1	0	0
4	95	1	0	1	0	1	0	0	1	0	0
..	..	..	..	..	..	..	..	..	0
40	135	1	0	1	0	1	1	0	0	1	0