Roll-up kite bag

Kyle Skopelitis, a very enthusiastic Doldrummer, designed and created the roll-up kite bag and kindly provided the plans for the bag for use by other Doldrummers and visitors to our website. The bag involves a LOT more work than a "normal" kite bag, but is well worth the effort.

Description - A practical storage unit for kites which is easily transportable and is easily adjusted/modified to accommodate up to 25 kites and other paraphernalia including lines, spares, feathers, spars, insulation tape etc.

The advantage of this design over a normal bag is that everything has its place and there’s no "hunting" around for stuff at the bottom of a bag. The following plans are only indicative and can easily be adjusted to suit individual needs.



The inside of the bag

The outside of the bag

 

Notes
a) The drawings are not to scale.
b) All measurements in cm.

Materials needed:


Construction
Main body

  1. Hot cut the sport bag nylon square (we will return to the main body later!)
  2. Sew the 3 pieces of webbing that will hold the securing straps in place onto the main body on the long ends of each piece of webbing, leaving at least 2.5cm for the securing straps.


    Mesh for winders, line, spares and accessories

    1. Cut the mesh in 2 lengths of approximately 150cm and about 17cm wide. Kyle used shade netting, but felt it was a bit too coarse and difficult to work with. Any relatively strong nylon mesh with wide (say 2mm+) openings should work.
    2. Seam one side of each strip with the 25mm webbing by folding the webbing double over the mesh and stitching (zigzag or straight) onto the mesh. Ideally the mesh needs to be sized according to the width of the kites so that the bag rolls evenly.
    3. Cut out the main body.
    4. Stitch the mesh to the nylon body (to the ends of the long sides as shown in the drawing). First stitch the sides and then stitch pockets (sew straight lines across the width of the mesh as indicated in the drawing) of approximately 15cm (slightly less if you calculate it correctly). Do NOT seam the sides before doing the spar pocket (see the last "Main body" section). The bottom of the pockets will be formed by the nylon as discussed in the "Main body" section.
    5. Don't stitch right to the side of the bag so that when the bag is rolled up, you’d get a smoother finish.
    6. Main body (again)

      1. Make a hole ± 4cm from the edge (top) of the bag, 1cm from the side (on either side) to allow for insertion of the spars. This should preferably done with a soldering iron.
      2. Fold the ends over (2cm) onto which the mesh is stitched and create a seam for the mesh and the top/bottom of the bag. Remember to use a rolled seam so that the nylon will not start to unravel later.
      3. Handle attachment webbing

        1. Mark the position for the D-rings on the main body (refer to the drawing of the outside of the bag), i.e. 15cm, 35cm and 45cm from the side of the main body.
        2. Stitch the webbing to the main body as shown in the drawing. Stitch the D-rings at the 15cm mark to the closest side of the bag and the other D-rings to the other side. This will make it easier to attach the clasps of the handles.
        3. Kites holder

          1. Fold the ripstop double, so that you have 2 x 75cm wide and 180cm long. Seam the length and turn the stitched "tube" inside out, with the seam now inside.
          2. Stitch the sides to the nylon body with a straight stitch (see drawing to determine placing of "Kites holder").
          3. Kyle suggested: "The width of each of the compartments is determined by the width of each kite in its bag. The measurements indicated are those that were suitable for my requirements. Each compartment is measured as follows:

            Main body (again)

          1. A spar pocket is stitched along the entire length of the bag (fibreglass spar or a spare carbon graphite spar) to give some rigidity and also provide a point from which to start the roll. This pocket should be sewn on AFTER the mesh has been sewn onto the body. The pocket should be approximately 1cm wide (i.e. 2cm folded over).
          2. Handles

            1. Slide a spring-loaded clasp over a 100cm piece of webbing, fold the end of the webbing over and stitch with a straight stitch. Repeat on the other side and for the other 100cm webbing.
            2. The handles are hooked onto the D-rings ("Handle attachment webbing").
            3. If you want to, cut a 7.5cm x 50cm strip of leather. Insert some snap rivets at the ends and fold over the handles to make carrying more comfortable.
            4. Securing straps

              1. Slide the securing straps through the 3 holes as indicated.
              2. Slide a male clasp over one side of each securing strap, fold the end of the webbing over and stitch with a straight stitch. Repeat on the other side with the female parts of the clasps.

              3. AFTER ALL OF THAT THE KITE BAG SHOULD BE READY!