|
MODEL
|
Protek Price
List 2003
|
PRICE
|
|
303
|
Power
Supply with Analog Display
Continuously variable Voltage and Current output on all models
30V/10A, 60V/5A, 30V/3A and 30V/2A models Short circuit and overload
protected Separate meters for monitoring voltage and current
Excellent regulation and ripple specs Constant Voltage and Constant
current indicators Ideal for the service bench Cost effective
|
$199.00
|
|
304
|
3
1/2 Digit AC/DC Mini Clamp-On
Meter
Measures AC/DC current to 1000A Manual ranging
Measures Volts, Amps and Ohms 1.37" Jaw opening for cramped
wiring locations Overload protection with indicator Data hold
Fused input Meets IEC-1010 Category III 600V safety standards
|
$149.00
|
|
305
|
3
3/4 Digit True RMS AC/DC Clamp-On Meter
Measures AC/DC current to 1000A True RMS AC Measurements
Auto/Manual ranging Frequency counter 40 segment analog bar graph
2-1/4" Jaw opening Meets IEC-1010 Category III 600V Safety
Standards
|
$199.00
|
|
307
|
3 3/4 Digit True RMS AC/DC Clamp-On Meter
Measures AC/DC current to 1000A True RMS AC Measurements Measures
true power, apparent power and power factor Auto/Manual ranging
Frequency counter 40 segment analog bar graph 2-1/4" Jaw
opening Meets IEC-1010 Category III 600V Safety Standards
|
$239.00
|
|
310
|
Power
Supply with Analog Display
Continuously variable Voltage and Current output on all models
30V/10A, 60V/5A, 30V/3A and 30V/2A models Short circuit and overload
protected Separate meters for monitoring voltage and current
Excellent regulation and ripple specs Constant Voltage and Constant
current indicators Ideal for the service bench Cost effective
|
$409.00
|
|
506
|
3
3/4 Digit DMM with Temp, Freq and Capacitance
Dual display for Frequency, AC voltage and Temperature measurements
True RMS AC Voltage, Current and DB Readings RS-232 interface &
software, 10 location memory Min, Max, Avg and Relative modes
Capacitance, Inductance, Frequency and Temp measurements Square wave
generator, logic function and back light
|
$169.00
|
|
605
|
Power
Supply with Analog Display
Continuously variable Voltage and Current output on all models
30V/10A, 60V/5A, 30V/3A and 30V/2A models Short circuit and overload
protected Separate meters for monitoring voltage and current
Excellent regulation and ripple specs Constant Voltage and Constant
current indicators Ideal for the service bench Cost effective
|
$500.00
|
|
608
|
50,000
Count, Advanced DMM with RS-232 Interface
DC accuracy 0.05% Low voltage Ohms measurement and conductance
Auto and software calibration Dual back-lit display and K type
thermocouple Measures duty cycle, pulse width and conductance
Compare function for go-no go testing Peak detection for capturing
high speed signals Binary bit expression bargraph AC and AC + DC
true RMS AC voltage and current measurements Auto/manual ranging
Test zener diodes up to 20 volts Min/Max/Avg relative modes Memory
store and recall Fuse protected current ranges Cat II 600V and CE
approved
|
$199.00
|
|
2700
|
Hand-Held
Frequency RF Power Meter
Battery operated for measuring power from 10MHz to 2GHz Measures RF
power continuously to 0.5 Watt Meter Hold and easy push-button zeroing
service Ideal for field use and bench service
|
$399.00
|
|
3025
|
Power
Supply with Analog Display
Continuously variable Voltage and Current output on all models
30V/10A, 60V/5A, 30V/3A and 30V/2A models Short circuit and overload
protected Separate meters for monitoring voltage and current
Excellent regulation and ripple specs Constant Voltage and Constant
current indicators Ideal for the service bench Cost effective
|
$169.00
|
|
3201
|
Hand-Held
2GHz RF Signal Strength Analyzer
Hand-Held and battery operated 100kHz to 2060MHz measurement range
Built-in 2GHz frequency counter Detects Wide band and Narrow band
FM, AM and Single Sideband Signals Phase lock loop for precise
frequency tuning RS-232 interface Up to 160 channels may be
scanned and displayed Audio output with built-in speaker
Detachable antenna included Back-lit display All functions are
menu selected Instrument setups & display data may be stored in
memory Includes software and RS-232 Cable Hard copy printer output
of spectrum and bar graph displays
|
$2,100.00
|
|
6502
|
20MHz
Dual Trace Oscilloscope with Alt-Mag
20MHz
Bandwidth Alt-Mag sweep for simultaneous display of main and X5
magnified trace 1mV/Div Vertical sensitivity Alternate trigger for
a stable display of unrelated signals X5 Sweep Magnification Large
6 inch CRT with internal graticule, for parallax free measurements
Autofocus Internal Sync separator circuit for stable triggering on
video signals Lightweight with low power consumption Supplied with
2 (X1, X10) probes and operating manual
|
$449.00
|
|
6506
|
60MHz
Dual Trace Oscilloscope,
Alternate trigger for a stable display of unrelated signals Alt-Mag
sweep for simultaneous display of the normal and X10 magnified trace
Autofocus Internal sync separator circuit for stable triggering of
video signals Internal sync separator circuit for stable triggering of
video signals Large 6 inch CRT with internal graticule for parallax
free waveform measurements Z axis input and CH 1 output Sweep
speeds to 10ns/Div 10kV acceleration voltage
|
$849.00
|
|
6510
|
Dual
Trace, Dual Timebase, 100MHz Oscilloscope
Four traces may be simultaneously displayed in ALT-sweep Five vertical
display modes: CH1, CH2, Dual, Add, Subtract Vertical mode triggering
for displaying 2 unrelated signals Trigger hold-off circuit for
synchronizing complex waveforms
Sweep speeds to 2nS/Div 12kV acceleration voltage for bright displays
of low duty cycle signals Z axis input
TV Synchronization for either line or field patterns 20MHz
bandwidth limit switch for triggering signals in a noisy environment
|
$975.00
|
|
7700
|
1GHz
Spectrum Analyzer/Adapter
Wide 10MHz to 1000MHz Frequency range Advanced DSP design converts any
oscilloscope into a 1GHz spectrum analyzer. Requires minimum 20MHz Dual
Trace Oscilloscope -90dBm sensitivity Resolution Bandwidths to
3kHz Direct CRT readout of frequency and signal level Can be used
for EMI and RFI compliance testing This Spectrum Analyzer is ideal for
testing AM, FM, CB, Cellular, Marine, Aircraft and Cable Television
equipment Troubleshoot IF and RF circuits, wireless products such as
two way radios, PCS, and cellular telephones, cable TV systems, wireless
remotes, microphones and monitors On-screen markers with freq and
level readouts Internal Calibration signal
|
$1,400.00
|
|
7800
|
2.6GHz
Spectrum Analyzer/Adapter
10MHz
to 2.6GHz frequency range Advanced DSP design converts any 20 MHz or
greater dual trace oscilloscope to a 2.6GHz spectrum analyzer
Resolution Bandwidths to 3KHz and zero span LCD reads out Frequency
and Amplitude LCD reads out Frequency and Amplitude Over 75dB of
display range Internal Calibration Range On screen markers
Ideal for testing AM, FM, CB, Cellular, Marine, Aircraft and Cable TV
equipment
|
$2,600.00
|
|
9301
|
1
Channel Synthesized Function/Arbitrary Waveform Generator
Log,
linear, phase continuous sweeps Frequency to 31MHz 0.01ľHz
frequency resolution 16 to 16K points arbitrary waveform lengths
Standard waveforms: Sine, Square, Triangle, Ramp and Noise Includes
waveform design software Waveforms may be designed via front panel or
software Sweep times to 1000s AM, FM and phase modulation
RS-232, GPIB and software interface
|
$1,500.00
|
|
9302
|
2
Channel Synthesized Function/Arbitrary Waveform Generator
Log,
linear, phase continuous sweeps Frequency to 31MHz 0.01ľHz
frequency resolution 16 to 16K points arbitrary waveform lengths
Standard waveforms: Sine, Square, Triangle, Ramp and Noise Includes
waveform design software Waveforms may be designed via front panel or
software Sweep times to 1000s AM, FM and phase modulation
RS-232, GPIB and software interface Dual independent channels (9302)
|
$2,999.00
|
|
3003B
|
Single
Output Power Supply with Digital Display
Constant Voltage or Constant Current operation Excellent load, line
and ripple specifications Fully isolated outputs allow for series
connections Coarse and fine voltage controls for accurate voltage and
current settings Indicators for constant voltage, constant current and
overload operation Noise free linear technology for servicing RF
circuits and high sensitivity amplifiers 3 Digit LED display for both
current and voltage
|
$271.00
|
|
3003R
|
Remote
Programmable Power Supply
Remote Sensing for precise regulation Remote analog programming for
both Constant Voltage and Constant Current modes Output load may be
turned on or off by remote control Series & Parallel Master/Slave
and Tracking operation Excellent Load, Line Regulation and Ripple
Specs LED display for both current and voltage All inputs and
outputs are isolated Fine and Coarse controls
|
$432.00
|
|
3005B
|
Single
Output Power Supply with Digital Display
Constant Voltage or Constant Current operation Excellent load, line
and ripple specifications Fully isolated outputs allow for series
connections Coarse and fine voltage controls for accurate voltage and
current settings Indicators for constant voltage, constant current and
overload operation Noise free linear technology for servicing RF
circuits and high sensitivity amplifiers 3 Digit LED display for both
current and voltage
|
$364.00
|
|
3006B
|
Single
Output Power Supply with Digital Display
Constant Voltage or Constant Current operation Excellent load, line
and ripple specifications
Fully isolated outputs allow for series connections Coarse and fine
voltage controls for accurate voltage and current settings Indicators
for constant voltage, constant current and overload operation Noise
free linear technology for servicing RF circuits and high sensitivity
amplifiers 3 Digit LED display for both current and voltage
|
$271.00
|
|
3015B
|
Dual
Output Power Supply with Digital Display
Noise free output for servicing RF equipment Energy saver design
allows cooler operation at all output levels for better stability and
operating life Excellent line and load regulation characteristics
Fully isolated outputs for series or parallel operation Coarse and
Fine voltage controls Each output has two 3 digit LED read-outs for
monitoring voltage and current Front Panel LEDs indicate constant
voltage or constant current operation and overload condition
|
$474.00
|
|
3032B
|
Dual
Output Power Supply with Digital Display
Noise free output for servicing RF equipment Energy saver design
allows cooler operation at all output levels for better stability and
operating life Excellent line and load regulation characteristics
Fully isolated outputs for series or parallel operation Coarse and
Fine voltage controls Each output has two 3 digit LED read-outs for
monitoring voltage and current Front Panel LEDs indicate constant
voltage or constant current operation and overload condition
|
$550.00
|
|
3033B
|
Triple
Output Power Supply with Digital Display
Noise free output for servicing RF equipment Energy saver design
allows cooler operation at all output levels for better stability and
operating life Excellent line and load regulation characteristics
Fully isolated outputs for series or parallel operation Coarse and
Fine voltage controls Output tracking Each output has two 3 digit
LED read-outs, for monitoring voltage, and current Front Panel LEDs
indicate constant voltage or constant current operation and overload
condition
|
$564.00
|
|
3040T
|
Triple
Output Power Supply with Series and Parallel Tracking
Outputs may be independent or connected in Series or Parallel and are
selectable from the front panel Fixed supply may be switched between
3.3V and 5.0V Series or Parallel Master/Slave tracking modes
Energy saving design
|
$490.00
|
|
3060R
|
Remote
Programmable Power Supply
Remote Sensing for precise regulation
Remote analog programming for both Constant Voltage and
Constant Current modes Output load may be turned on or off by remote
control Series &
Parallel Master/Slave and Tracking operation Excellent Load, Line
Regulation and Ripple Specs LED display for both current and voltage
All inputs and outputs are isolated Fine and Coarse controls
|
$487.00
|
|
5050S
|
Single
Output Power Supply with Digital Display
Constant Voltage or Constant Current operation Excellent load,
line and ripple specifications Fully isolated outputs allow for series
connections Coarse and fine voltage controls for accurate voltage and
current settings Indicators for constant voltage, constant current and
overload operation Noise free linear technology for servicing RF
circuits and high sensitivity amplifiers 3 Digit LED display for both
current and voltage
|
$651.00
|
|
6030R
|
Remote
Programmable Power Supply
Remote Sensing for precise regulation Remote analog programming
for both Constant Voltage and Constant Current modes Output load may
be turned on or off by remote control Series & Parallel
Master/Slave and Tracking operation Excellent Load, Line Regulation
and Ripple Specs LED display for both current and voltage All
inputs and outputs are isolated Fine and Coarse controls
|
$495.00
|
|
A450
|
Electronic
FET VOM
10
M input impedance Six resistance ranges enables measurements from 0.1
Ohm to over 1 Giga-ohm 4-12" mirror scale meter Meter pointer
can be set for zero center scale Reversing switch and power on
indicator
|
$55.00
|
|
A480B
|
300
Amp Analog Clamp-On Meter
Temperature measurement Meter Lock Switch freezes measured reading
for closer examination at safe location For use in plant
maintenance, HVAC, electrical installation, motor repair and similar
applications
|
$48.00
|
|
B2000
|
2GHz
Universal Counter
0.1Hz to 2GHz Frequency Range Measures Frequency, Period, Time
interval, Ratio and Totalize 0.5 PPM temperature stability Channel
A and Channel B have variable trigger level controls Large, bright 8
digit LED frequency display along with function and gate time indicators
Self check Low pass filters and X10 attenuators All functions
selected via tactile switches
|
$389.00
|
|
B3230
|
Dual
Input AC Millivolt Meter
Two
independent channels with independent meters 10Hz to 1MHz bandwidth
12 measurement ranges Measures AC volts, dBV and dBm Three
Color-coded scales 10 MW input impedance
|
$400.00
|
|
B4100
|
Bench
Top Programmable Digital Multimeter
5-1/2 Digit Multimeter with selectable count resolutions up to 200,000
True RMS and measures frequency Selectable Count Resolutions: 2k, 20k,
200k Auto-ranging Trend plot display RS-232 interface standard
and optional GPIB interface Min/Max/Avg, Relative error and comparison
functions May be used on line voltages from 85V to 250V without any
internal changes Software included Seven setups may be stored and
recalled in memory
|
$545.00
|
|
B801
|
Sweep
Function Generator 2MHz
Seven frequency ranges with 100:1 control on each range Built-in 2MHz,
4 digit frequency counter Less than 2% sinewave distortion
Variable symmetry DC offset and Voltage Controlled Frequency input
TTL sync output
|
$245.00
|
|
B803
|
Sweep
Function Generator 2MHz
Seven
frequency ranges with 100:1 control on each range Less than 2%
sinewave distortion Variable symmetry DC offset and Voltage
Controlled Frequency input TTL sync output
|
$320.00
|
|
B810
|
Sweep
Function Generator 10MHz
Wide (0.01HZ to 10MHz) Frequency Range Burst and Triggered mode
Sweep start/stop capability Six digit LED frequency readout Log.
or Lin. sweep Built-in 10MHz frequency counter External FM with
the VCG input Output can be amplitude modulated
|
$775.00
|
|
B813
|
100KHz
to 150MHz RF Signal Generator
100kHz to 150MHz Frequency range Output to 450MHz is possible using
the 3rd harmonic Two position attenuator plus fine control for setting
output voltage levels Internal and external modulation Highly
stable frequency output with external crystals Excellent on the
service bench and in the classroom
|
$177.00
|
|
B818
|
1GHz
Multifunction Counter
10Hz to 1GHz measurement range Frequency, Period and Totalize and Self
Check modes 8 digit LED display X1 and X10 Input Attenuator 10
PPM temperature stability (oven controlled) Low power consumption and
light weight 25mV sensitivity
|
$275.00
|
|
B845
|
Bench
Top Digital Multimeter
4-1/2 digit LCD display with polarity indicator .05% DC voltage
accuracy 10ľV AC & DC voltage resolution 10nA current
resolution 10mW Resistance resolution Data hold switch
Measures current to 10 Amps 200ľA AC/DC Current Range
|
$275.00
|
|
B850
|
10Hz
to 1MHz Wide Range Audio Generator
Wide 10Hz to 1MHz Frequency range Low distortion Sine wave and
Square wave output Lightweight, Rugged construction Frequency
setting via large frequency dial Ideal for classroom or audio bench
|
$183.00
|
|
B940
|
3
3/4 Digit 4000 Count True RMS Bench Top DMM with RS232
True RMS AC volts and amps measurements Capacitance and Frequency
measurements Back-lit display and Auto/Manual ranging MIN/MAX and
Relative mode Delay hold mode AC Line or Battery Operated
RS-232 Interface with software
|
$149.00
|
|
C3100
|
Programmable
2.4GHz Universal Counter
Highly accurate frequency measurements to 2.4GHz Measures Frequency,
Period, Duty Cycle, RPM, Frequency ratio, Difference frequency, Time
interval and Totalize Nine measurement functions Plots trend graph
on LCD display Compare, Relative Error and Min/Max functions
Standard RS-232 with optional GPIB interface Eight setup screens may
be saved and retrieved from memory Software for controlling,
displaying data and data logging Operates on all line voltages from
85V to 270V without any changes
|
$429.00
|
|
CL200
|
3
1/2 Digit 2000 Count L/C Meter
Six
capacitance ranges and four inductance ranges High accuracy
measurement Automatic zeroing Low battery indicator Fuse
protected input Includes holster
|
$68.00
|
|
CM109
|
LCD
Capacitance Meter
Measures capacitance to 20mF Zero adjust Fused input Large LCD
display Rugged case design Inputs for clip leads and lead
Insertion
|
$89.00
|
|
CM110
|
Capacitance
Meter
Zero adjust for compensating stray capacitance Large easy to read
3-1/2 digits, 2000 count LCD 0.5% measurement accuracy Fused input
9 measurement ranges Three measurement frequencies Includes
holster
|
$85.00
|
|
D1200D
|
1200
Amp AC Clamp-On Meter
Maximum current is 1200A Data hold function Full auto-ranging on
AC/DC Volts and Ohms Has audible buzzer for "no-look"
continuity plus diode test 3-1/2 Digit 2000 count
|
$109.00
|
|
D14000
|
Digital
Insulation Tester
Measures insulation resistance to 2000MW Measures AC volts Data
hold and backlight 3-1/2 digits, 3200 count LCD Designed to
IEC-1557-2 standards Rugged case and lightweight 125, 250V and
1000V test voltages
|
$225.00
|
|
D640AB
|
Clamp
DMM 600 AC AMP
Measures AC current to 600 Amps 3-3/4 Digit 4000 count Analog bar
graph Auto-ranging Continuity, buzzer and diode test 2"
Jaw opening Resistance to 40MW
|
$75.00
|
|
D7510C
|
100Ms/S
Digital Storage Oscilloscope
100
MHz Analog bandwidth 100Ms/S real time sampling rate and 10GS/s
Equivalent time sampling 16K record length for each channel Ultra
zoom for viewing waveform details FFT function High resolution 320
x 240 Pixel Monochrome LCD display Optional 256 Color VGA LCD display
Optional extension module for RS232 and GPIB interfaces with ultra
zoom software Automatic waveform measurements Auto-setup and auto
calibration 5 waveforms and setups may be stored in memory
|
$1,314.00
|
|
D7510M
|
100Ms/S
Digital Storage Oscilloscope
100 MHz Analog bandwidth 100Ms/S real time sampling rate and 10GS/s
Equivalent time sampling 16K record length for each channel Ultra
zoom for viewing waveform details FFT function High resolution 320
x 240 Pixel Monochrome LCD display Optional extension module for RS232
and GPIB interfaces with ultra zoom software Automatic waveform
measurements Auto-setup and auto calibration 5 waveforms and
setups may be stored in memory
|
$1,177.00
|
|
D901
|
UL
Approved 2000 Count DMM
UL & CE approved Large easy to read 3-12 digit LCD display
Ready to use with batteries installed Pocket size and low cost
Single rotary switch for all functions and ranges
|
$25.00
|
|
D905
|
3
1/2 Digit 2000 Count Value-Priced DMM
10MW input impedance Measures DC current to 10 Amps Measures
resistance to 20MW Continuity buzzer Diode test Low battery
indicator Holster included Data Hold Function
|
$49.00
|
|
D930A
|
Shirt
Pocket Auto-Ranging 2000 Count DMM
Auto ranging with continuity buzzer Data hold and diode test Large
easy to read LCD display Uses std "AAA" batteries
Overload protection on all ranges Rear case has probe and cable
compartment Great for automotive
|
$39.00
|
|
D935A
|
Probe
Type Auto-Ranging 2000 Count DMM
Designed
for safe, one handed operation Auto ranging for all functions Has
data hold, diode test, and continuity buzzer Large easy to read LCD
display 10MW input resistance
|
$44.00
|
|
D980
|
3
3/4 Digit 3200 Count Value-Priced DMM with Bargraph
Meets UL standard 1244 3200 count bargraph Measures AC/DC
current from 300ľA to 12 Amps Operates on (2) 1.5 AAA batteries
0.5% DC accuracy Measures resistance to 30MW Continuity and Diode
check Data hold, Range and function select buttons Low battery
indicator Holster included
|
$75.00
|
|
D981
|
3
3/4 Digit DMM with Temp, Freq and Capacitance
3-3/4 digit LCD with Bargraph and Data Hold Temperature, Frequency and
Capacitance measurements Min/Max and relative modes Auto power off
10MW input impedance
|
$109.00
|
|
DI2001
|
Cat.
III Digital Insulation Tester
Measures insulation resistance to 2000MW 250V, 500V and 1000V test
voltages Meets IEC 1010-1, Category III-600V safety standards Data
and Max hold 3-1/2 digit, 2000 count LCD Continuity buzzer
|
$169.00
|
|
FC250
|
Hand-Held
Frequency Counter
Hand-held
and battery operated Measures frequencies to 2.5GHz in 3 measurement
ranges Large 8 digit LCD display High sensitivity on all ranges
MIN/MAX/AVG functions Relative frequency measurements Period
measurement Auto power-off and data hold
|
$249.00
|
|
G5100
|
Programmable
15MHz Sweep/Function Generator
0.1
to 15MHz frequency range Low Distortion (< 1%) Direct Digital
Synthesis for high stability All functions are selected and stored via
front panel Sweep time to 10 sec 7 setups may be stored in memory
and recalled later All functions controllable by the RS-232 or
optional GPIB interface May be operated at line voltages from 85V to
270V without internal changes or switching
|
$399.00
|
|
P3502C
|
20MHz
Dual Trace Scope with Comp-Test
Wide Bandwidth & high sensitivity Built-in component tester
displays L, C, R, diode and transistor characteristics The best
price/performance available from any oscilloscope High brightness CRT
with internal graticule Front panel electrical trace rotator High
frequency rejection filter trigger circuit TV Video Synch Filter
|
$399.00
|
|
P6000
|
Programmable
Power Supply
All
values may be entered from keyboard or rotary dial RS -232/485
interface with cable, adapter and software CD Volts, amps and power
are displayed on a backlit LCD display 10 settings may be stored in
memory Light weight and energy efficient Over voltage and current
protection Outstanding in Production Test Applications
|
$299.00
|
|
S2401
|
50Ms/S
1MHz Hand-Held Scope Meter
Dual Channel 50MS/s sampling rate 1mV/Div Vertical sensitivity
Auto ranging Vertical and Horizontal scales Built-in auto/manual
ranging 4000 count DMM DC to 1MHz bandwidth Hand held and battery
operated Designed to UL3111, CSA C22.2 No 1010 standards RS-232
Port and supplied software User-friendly front panel
|
$325.00
|
|
SL-100
|
Sound
Level Meter
Meets ANSI and IEC 651 Type 2 standards 3-1/2 digit LCD display
A&C frequency weighting 0.1dB resolution Maximum hold
function Internal calibration check Fast and slow response
Analog output jack
|
$229.00
|
|
T-100
|
Photo
and Contact Tachometer
A
photo and contact tach in one instrument Measures RPM and surface
speed Records the minimum, maximum last value 0.5 to 100,000 RPM
measurement range 0.05% accuracy 5 Digit LCD
|
$239.00
|
|
TM1300K
|
4-1/2
Digit Dual Input Thermometer
Measures temperature differences F° or C° is selectible Data
Hold Analog millivolt output Thermocouple probes included
|
$99.00
|
|
Z8200
|
LCR
Meter
Measures L, C, R, |Z|, Q and D Displays component value, Q or D,
Delta, or Delta% 5 digit display for component value and Q/D Auto
ranging or Range hold Built-in comparator with 4 bin-sorting function
Open and short circuit calibration for accurate zeroing Series and
parallel equivalent circuit modes Three test frequencies Warning
alarm for pass or fail binning Easy to use
|
$580.00
|
|
Z9216
|
High
Accuracy, Wide Range LCR Meter
0.2% basic accuracy Wide measurement range over13 orders of magnitude
Store and recall 9 instrument setups Measurement rates to 20 times
per second Test frequencies are 100Hz, 120Hz, 1kHz, 10kHz and 100kHz
Displays component value and Q or Dissipation factor Averaging for
2 to 10 measurements RS-232 and optional GPIB and Handler interface
Open and short circuit compensation for accurate zeroing Easy to
use and calibrate Built-in calibration procedures Binning
capabilities
|
$1,750.00
|
