How to update your card!:
SELECT YOUR DECODER:
AMSTRAD BARCOM
CAMBRIDGE ECHOSTAR FILMNET
FINLUX
FUBA GRUNDIG MACAB
LENSON LUXOR NOKIA
NOMEX ORIGO
PACE PHILLIPS SALORA
TRIASAT TRIAX OTHERS
600.
! It's always the
buttons in the blue field that is used.
1. Push select.
2. Push arrow down and choose
CARDCONTROL.
3. Push SELECT.
4. Push ARROW down and choose NEW SECRET CODE.
5. Push SELECT.
6. Choose correct digit with ARROW up or ARROW
down.
7. Push SELECT in order to come to next digit.
8. Repeat with all 7 groups of digits.
srd 650.
1. Push
MAC MENU once.
2. Choose CARD.
3. Choose CARDCONTROL.
4. Choose NEW SECRET CODE.
5. To choose digits Push
'function' buttons beside MAC MENU.
6. Push MAC MENU to alternate
to next digit.
7. When you have typed the four first digits, Push
STORE.
8. Repeat with all 7 groups of digits.
srd 850.
1. Push
on MENU.
2. Push on 9.
3. Push on 2.
4. Push on 4.
5. When you have typed the four first digits, Push
STORE.
6. Repeat step 1-5 for the other digits.
MAC 301.
1. Push
MENU.
2. Go to ACCESS and Push
INDEX.
3. If your decoder ask you to INSERT YOUR
CODE, Push 0000.
4. IN other cases go to INSERT NEW CODE and Push
on INDEX.
5.Type the first four digits. Thr decoder ask
you to verify.
6. Repeat step 4-5 for all 8 groups of digits.
1. Go to the channel
you wanna update.
2. Push MENU button.
3. Choose MAC menu.
4. Push OK.
5. Push OK (again).
6. Choose ACCESSCONTROL.
7. Push OK.
8. Choose NEW SECRET CODE.
9. Push OK.
10. Enter the first 4 figure in the 7x4
figured code.
11 Repeat the first 4 figure in the 7x4
figured code.
12. When this is done, will you automaticely
go out agin.
13. Then just repeat until all 7 codes are
entered.
SR/LT8700.
1. Push
on PPV.
2. Push on ARROW down and
choose 'Lower option'.
3.Push on SELECT.
4. Choose '4th option' with arrow-button.
5. Push on SELECT.
6. Push in the four first
digits.
7. The dekoder takes you to step 1.
8. Push PPV,SELECT,SELECT and
type next four digits.
Orginal leasedecoder from Filmnet.
A part of these decoders where
sold without remotecontrol. The update
is done with the two buttons that
exists on decoder front.
If you have remotecontrol, look at
Philips STU901. If you not,
try the following. We call the two
buttons on the
decoder "MENU" and
"ARROW".
1. Push
MENU and a menu comes up on your TV.
2. Use ARROW to get down to 4
(Accession).
3. Push MENU
again in order to choose accession .
4. If the decoderask you to TYPE
YOUR CODE, type: 0000.
Otherwise
just go to next step.
5. In the new menu that comes up,
use ARROW to 2 (change personal code).
6. Push
MENU.
7. Push ARROW
until desired digit is shown.
8. Push MENU, and
you will 'jump' to next digit.
9. Choose next digit with ARROW
and Push MENU.
10.Go to third digit. Type with ARROW and Push
MENU.
11. Type last digit with ARROW and Push
MENU.
12. You hav now typed the the first four
digits. Since this decoder accepts 12
digits
PIN-codes you may have to Push several times on
MENU in order to continue.
13. The decoder ask you to Push
the four digits once more for verifikation.
14. Repeat the other 7 groups of 4 digits.
ATTENTION. Every time you type
a new code
the decoder ask you to type the current code. Instead of
typing 0000,
you should
type the last code. If you for example shall type the third
digits, you have
to type
the second digits as current code, and so on.
5900 S.
1. Push MENU.
2. Use up/down-arrow to ACCESS.
3. Push OK.
4. Use up/down-arrow to ACCESS.
5. Push OK.
6. If the decoder ask you to TYPE
YOUR CODE, type 0000.
7. If not mark TYPE IN NEW CODE
with up/down-arrow.
8. Push OK, or
right arrow.
9. Type the first four digits. If
the decoder ask you to confirm, type it once more.
10. Choose TYPE NEW CODE, type next four
digits and so on.
Mac 9.
1. Push MENU.
2. Use up/down-arrow to ACCESS.
3. Push OK.
4. Use up/down-arrow to ACCESS.
5. Push OK.
6. If the decoder ask you to TYPE
YOUR CODE, type 0000.
7. If not mark TYPE IN NEW CODE
with up/down-arrow.
8. Push OK, or
right arrow.
9. Type the first four digits. If
the decoder ask you to confirm, type it once more.
10. Choose TYPE NEW CODE, type next four
digits and so on.
STR 535/N MAC,STR 635.
1. Choose
the channel you shall update and check that its coded.
If you have more than
one smartcard than the one that you shall update,
pull out the other
one.
2. Push MENU, go to MAC menu
and press OK.
3. Choose access menu 1 or access menu 2
depending on wich cardslot you .
have the card. 1=left
and 2=right. Press OK.
4. Choose access and Push OK,
go to New secret code and Push OK.
5. Type the four first digits. Type the same
digits again.
6. Repeat until all codes are typed.
7. Leave the menu. The card is uppdated.
(If you typed the correct code!).
NRF 500,530,600,660,700.
1. Push
MENU, choose UPPER or LOWER CARDINFO depending on
which cardslot you
use.
2. Choose MAC LOCK, and type 0000 as SECRET
CODE.
3. Go to NEW CODE, and type the four first
digits.
4. Push STORE two
times.Message 'Remember your code' confirms if you succeed.
5. Go to NEW CODE, and type next four digits, Push
STORE two times. and so on.
6. When you have typed all digits, choose
conclude 2 times.
Lenson
1. Menu ( on
remote control )
2. Go to "Mac menu" then OK button
3. "Accessmenu" OK button
4. Then "accesscontrol" OK button
5. Then "New secret kode" OK button
6. Only enter new code
Note, you have to
confirm code every time.
Totally you have to go
through the above 7 times.
Mac 3.
1. Go in in
the menu, choose YELLOW button for access.
2. Push '+' in order
to mark ACCESS.
3. Push INDEX.
4. If the decoder ask you to TYPE IN YOUR
CODE, type 0000.
5. Choose ALTER YOUR CODE with '+' and INDEX.
6. Type the four first digits.
7. Push optional button.
8. Push INDEX again, choose
ALTER YOUR CODE with '+' and INDEX.
9. Type next four digits. Repeat all digits.
Mac IV, Mac V,STM 970.
1. Push MENU.
2. Use up/down-arrow to ACCESS.
3. Push OK.
4. Use up/down-arrow to ACCESS.
5. Push OK.
6. If the decoder ask you to TYPE
YOUR CODE, type 0000.
7. If not mark TYPE IN NEW CODE
with up/down-arrow.
8. Push OK, or
right arrow.
9. Type the first four digits. If
the decoder ask you to confirm, type it once more.
10. Choose TYPE NEW CODE, type next four
digits and so on.
Mac V, 8003 S .
1. Push MENU.
2. Use up/down-arrow to ACCESS.
3. Push OK.
4. Use up/down-arrow to ACCESS.
5. Push OK.
6. If the decoder ask you to TYPE
YOUR CODE, type 0000
7. If not mark type NEW CODE with
up/down-arrow.
8. Push OK, or
right arrow.
9. Type the first four digits. If
the decoder ask you to confirm, type again.
10. Choose TYPE NEW CODE, type next four
digits and so on.
1. Choose the
channel you wanna update.
2. Push [PAY] to go to ACCESS MENU.
3. Push on + until ACCESSCONTROL stands whit
green then push PAY.
4. Push on + until NEW SECRET. CODE stands
whit green then push PAY.
5. Now the text will blink NEW CODE then you
enter the the first 4-figure code.
6. The last 4-figured codes is entered
the same way.
7. The last used menu choice whith green is
automatic green, then push 3 times on PAY
it will automaticly go
to NEW CODE in your screen.
1. Push
pay.
2. Choose cardcontrol.
3. Choose new secret code.
4. Type the four first digit with + -
buttons
5. Push pay in order to leave
the menu
6. Repeat 7 times. Use merely pay and + -
buttons
mrd 260. ATTENTION! Pace 260 of 97-year model, can not
be updated with the remote.
Contact your supplier.
1. Push
MENU.
2. Choose ACCESS MENU.
3. Choose CASS CONTROL.
4. Too NEW SECRET CODE.
5. Type the first four digits. Conclude with
right arrow.
6. Repeat with the rest of the digits.
mrd 400.
1. Push
MENU.
2. Push on 9.
3. Push on 2.
4. Push on 4.
5. Type the first four digits, store with
STORE.
6. Repeat moment 1-5 with the other digits.
mrd
960+.
1. Go to
MENU.
2. Choose 6-ACCESSMENY.
3. Choose CARDCONTROL.
4. Choose NEW SECRET CODE.
5. Type the first four digits.
6. Repeat moment 1-5 for the other digits.
STU 901,BDE 353.
1. Push
MENU.
2. Choose 4 (ACCESSION).
3. Choose 2 (CHANGE OF PERSONAL CODE).
4. Type the first four digits two times.
5. Choose 2 (CHANGE OF PERSONAL CODE).
6. Type the old digits once, and then the NEW
digits TWO times.
7. Repeat moment 6 and 7 with all 8
digits.
8. Importantly. Always type last code ONCE,
before type the new TWO times.
STU1400 Decoder: Philips BDE353 (double cardslots)
1. Choose the D2mac channel that you want to update.
2. Use remotecontrol and press
SAT2 button (in order to choose decoder).
3. Push on MENU
(green button)
4. Choose 4 (Accesskontroll card
1) or 5 (Accesskontroll card 2)
5. Choose 2 (change personal
code).
6. Type the first four digits
(xxx0)
7. Choose 2 (change personal
code).
8. Type next four digits (xxx1)
9. Choose 2 (change personal code)
and repeat with the other digits
(xxx2,
xxx3, xxx4, xxx5, xxx6).
10. It will take less than 30 seconds before
the image comes.
11. Push MENU.
Salora.
MAC 3.
1. Push
MENU.
2. Go to ACCESS and Push
INDEX.
3. If your decoder ask you to INSERT YOUR
CODE, Push 0000.
4. IN other cases go to INSERT NEW CODE and Push
on INDEX.
5.Type the first four digits. Thr decoder ask
you to verify.
6. Repeat step 4-5 for all 8 groups of digits.
SR 4007.
1. Choose
the channel you shall update and check that its coded.
If you have more than
one smartcard
than the one that you
shall update, pull out the other one.
2. Push MENU, go to MAC menu
and Push OK.
3. Choose access menu 1 or access menu 2
depending on
wich cardslot you have
the card. 1=left and 2=right. Push OK.
4. Choose access and Push OK,
go to New secret code and Push OK.
5. Type the four first digits. Type the same
digits again.
6. Repeat until all codes are typed.
7. Leave the menu. The card is
uppdaterat. (If you typed the correct code!).
1. No description available. Please check out Other.
Others.
1. It's the possibility that alter SECRET CODE or PIN-CODE
on your
decoder that shall be used.
2. Seek up the button on your
remotecontrol that opens the decoder- menu.
3. When you Push
on this a square on your TV pops up with
miscellaneous
adjust alternativ.
4. Choose the function that gives
you access tothe cards functions.
5. After that it will presumably
pop up a new menu.
6. Here you usually are able to
choose between channelinformation and access.
7. Choose ACCESS.
8. If the decoder ask you to TYPE
SECRET CODE, type 0000.
9. You should now enter a new menu
where you can TYPE NEW CODE.
10. Choose this alternative, and type the four
first digits.
11. When most decoders ask you to confirm this
just type the digits again.
12. When this is done, you will get back to
the menu TYPE NEW CODE.
13. Mark TYPE NEW CODE and repeat with next
four digits.
14. On some dekoders you will need to
TYPE SECRET CODE each time before
you can
TYPE NEW CODE. Type 0000 as SECRET CODE, and the four
new digits
as NEW CODE.